三菱 CL1X4 三菱-CL1X4-D1B2 用戶 手冊
資料介紹：
Wa
Mi
ca
pro
fac
pro
• T
i
d
Th
do
re
a
4.2 Connection to sensor
Positive common (NPN)
• When using a two-wire type sensor y When using a three-wire type sensor
• When using a three-wire type sensor
(when using the power supply for sensor other than 24V DC)
Negative common (PNP)
• When using a two-wire type sensor y When using a three-wire type sensor
• When using a three-wire type sensor
(when using the power supply for sensor other than 24V DC)
Bleeder resistor *1
Connected to DC 24A terminal
COMB
Connected to DC 24A terminal
COMB
Detection
circuit
Sensor (NPN)
X *
Detection
circuit
X *
COMB
Detection
circuit
X *
COMB COMB
Bleeder resistor *1
Connected to DC 24A terminal Connected to DC 24A terminal
Detection
circuit
Sensor (PNP)
X *
Detection
circuit
X *
COMB
Detection
circuit
X *
4.3 Crimp-style terminal
For I/O wiring, use crimp-style terminals of the following dimensions.
Use a crimp-style terminal in a status in which no force is applied on the cable.
4.4 Module terminal screw
Tighten the terminal screws (M3 screws) on the terminal block with a tightening
torque of 42 to 58 N⋅cm.
5. Specifications
5.1 General specifications
Applicable crimp-
style terminal
• RAV1.25-3
• V1.25-3 (manufactured by JST Mfg. Co., Ltd.)
• 1.25-3 and TG1.25-3 (manufactured by NICHIFU Co., Ltd.)
Applicable wire size 0.3 to 1.25 mm2
6.2 mm (0.24" )
or less
6.2 mm (0.24" )
or less
Terminal
Terminal screw
Crimp-style
terminal
Terminal screw
Crimp-style
terminal
When wiring one cable to one terminal When wiring two cables to one terminal
Terminal
φ 3.2 (0.13") φ 3.2 (0.13")
Item Specification
Ambient
working
temperature
0 to 55°C (32 to 131°F)
Ambient storage
temperature
-25 to 75°C (-13 to 167°F)
Ambient
operating
humidity
5 to 95%RH: Dew condensation shall not be considered.
Ambient storage
humidity
5 to 95%RH: Dew condensation shall not be considered.
When intermittent vibration is present
Number of times of
sweep
*4 This index indicates the degree of conductive generating substances in the
environment in which the module is used. The degree of contamination 2
indicates that contamination is caused by generation of only non-conductive
substances.
In this degree, however, temporary conduction may be caused by accidental
condensation.
5.2 Input specifications
5.3 Performance specifications
Item Specification
Input method DC input (External power supply of the input part)
Number of inputs 4 points
Isolation method Isolation with photocoupler
Rated input voltage 24V DC
Rated input current Approx. 4 mA
Operating voltage range
20.4 to 28.8V DC (24V DC -15% to +20%)
Ripple ratio: Within 5%
Max. simultaneous ON
input points
100% (at 24V DC)
ON voltage/ON current 19 V or more/3 mA or more
OFF voltage/OFF current 11 V or less/1.7 mA or less
Input resistance 5.6 kΩ
Response
time
OFF→ON 0.5ms/1.5 ms or less (at 24V DC)
Selected by DIP switch (default value = OFF/1.5ms).
ON→OFF
0.5ms/1.5 ms or less (at 24V DC)
Selected by DIP switch (default value = OFF/1.5ms).
Common wiring method
4 points/1 common (2 points)
(terminal block two-wire type)
Item Specification
Module
power
supply
Vol tage
20.4 to 28.8V DC (24V DC -15% to +20%)
Ripple ratio: Within 5%
Current
consumption
40mA (when all points are ON)
Initial current 70mA
Max. allowable
momentary power
failure period
PS1:1ms
Number of stations
occupied
4-, 8- or 16-point mode: 1 station
6
49(1.93") 4.5(0.18") 40(1.58")
處理速度更快的CPU Q04UDHCPU
編碼器接頭 MR-J3JCBL03M-A1-L
連接電纜 AC50TE
CPU單元 A1SJCPU
耐油蓋 GT10-20PCO
QCPU（Q模式）用總線連接電纜 GT15-QC200BS
通用型CPU Q00UCPU
CPU單元 A4UCPU
伺服電機 HC-SFS3524B
大型CPU擴展電纜 GT15-AC06B
連接器 A6CON2
伺服電機 HC-KFS053
CPU單元 A0J2HCPUR21
伺服馬達 HC-UFS502B
編碼器電纜 MR-JCCBL20M-H
運動CPU單元 A73CPUP21-S3
帶基板的小點數CPU Q00JCPU-S8-SET
電磁制動器用電纜 MR-BKS1CBL5M-A2-L
帶以太網類型的Q系列CPU Q20UDEHCPU
RS-485端子臺轉換電纜 FA-LTBGTR4CBL20
緊停開關導桿 GT11H-50ESCOV
伺服電機 HC-SFS7024B
溫度傳感器用模塊 FX2N-4AD-TC
CPU單元 A2NCPU
擴展電纜 QC05B
MODBUS接口模塊 A1SJ71UC24-R2-S2
上位控制器連接模塊 A0J2C25
串行通信模塊 A1SJ71QC24N-R2
伺服電機 HC-SFS81
編碼器接頭 MR-J3ENCBL5M-A2-L
上一條：
下一條：相關下載
